Glossary: explanations of products and services
Glossar (EN)
We explain you the most relevant words.
| Dismounting of damming | Cutback of device made of elastomer, steel or wood to process the epoxy materials in the intended area and to prevent distribution |
| Torque | Measure for tightening the bolts in the chockfast in Nm to prevent an overload of the epoxy (max 4.5 N / mm²) |
| Alignment | Adjustment of e.g. shafts to each other to avoid high bearing loads and vibration |
| Barcol hardness | Measure for the hardening of GFK, here for Chockfast to check the correct mixture of resin and hardener and their hardening process (GL specification for example 35 Barcol) |
| Calculation | Calculation of the surface pressure on Chockfast material by using the weight of the machine and the tightening torque of bolts, also in some cases the stretching of the bolts is checked |
|
Chockfast orange |
Epoxy for the marine sector, approved by almost all classification societies for shipbuilding |
|
Chockfast black |
Epoxy for casting of high temperature machinery |
|
Chockfast gray |
Epoxy for the casting of e.g. Rails, bigger shrinkage than Chockfast orange |
|
Chockfast red |
Epoxy for the casting of, for example, anchor bolts and casting height up to 450mm |
|
Chockfast red SG |
Epoxy for the casting of e.g. Compressors, pumps, electric motors and gearboxes in the industrial sector, casting height up to 100mm |
| Densit® | Grouting material (concrete based) with low shrinkage from ITW |
| Ducorit | Grouting material (concrete based) with low shrinkage from ITW |
| Epocast | 2K Epoxy, alternative from MIM: Chockfast orange |
| Damming | Device made of elastomer, steel or wood to process the epoxy materials in the intended area and to prevent distribution |
| Submission | Record of calculations, drawings and project description for approval by the classification societies |
| Five Stars | 2K Epoxy, alternative from MIM: Chockfast orange |
| FEROFORM | Manufacturer of composite bearing materials based in Manchester / UK |
| Foundation plan | Drawing for the dimensions of the Chockfast chocks including the calculated bolts |
| Foundation drawing | Plan for the dimensions of the Chockfast chocks including the calculated bolts |
| Dangerous goods | Materials which have to be handled with special care and registered with a UN number for transport (road, ship, plane) |
| Loctite Marine Chocking | 2K Epoxy, alternative from MIM: Chockfast orange |
| Classification societies | Company that acts as a kind of expert in the shipping sector such as DNVGL, ABS; Bureau Veritas etc. for shipowners, insurance companies and much more. |
| MecLev | Height-adjustable metal fitting |
| Mixer | Standing compulsory mixer for 3K materials such as Chockfast red and red SG |
| Philybond No. 6 | Kneadable 2K epoxy for temperatures up to 220 ° C |
| Phillybond orange | Trowelable permanently elastic epoxy for e.g. Stern tube seals |
| Phillymastic | TG7B Liquid or Paste is an epoxy for storage of eg LNG and LPG tanks for temp. Up to - 150 ° C |
| Railko | Manufacturer of composite bearing materials based in Manchester / UK |
| Reduction | Reduction in the amount of hardener in Chockfast orange for setting the material for various specific applications |
| Repair Compound | 2K epoxy for filling, smoothing and gluing metal, wood, plastic or concrete materials. Resistant to oils, fuels and salt water |
| Rotachock | Height-adjustable metal fitting, alternative MecLev |
| Rudder coker | Passage through the hull for the shaft of the rudder |
| Stirrer | Specially shaped mixer for drilling machine to prevent air from accumulating in the epoxy during mixing |
| Rocol | Release spray to prevent the adhesion of Epoxys to surfaces |
| Sterntube | Wave tunnel through which the ship's shaft leaves the ship. Construction with different bearings and sealing system |
| Shrinkage | Change in the dimensions of Epoxys before / after curing, expressed in mm per mm pouring height (mm / mm) |
| Tenmat | Manufacturer of composite bearing materials based in Manchester / UK |
| Pot life | Period of time in which processing of Epoxys is possible after all components have been assembled |
| Release spray | Spray to prevent the adhesion of Epoxys, e.g. Rocol or Winix |
| Working temperature | Temperature range in which a processing and curing of Epoxys is possible (Chockfast about 15 ° C to about 32 C). |
| Vibracon | Height-adjustable metal fitting, alternative MecLev |
| WINIX | Separating spray for Chockfast red / red SG to connect with e.g. to prevent the containment |
| Crankshaft deflection | Movement of the crank webs during the rotation of the crankshaft in the motor housing, e.g. for the detection of bearing problems |
